MC2102 Tube Power Amplifier Features
CUSTOM OUTPUT TRANSFORMER
Unique McIntosh-wound transformer delivers the full rated amplifier output with the least possible distortion and maximum bandwidth into loudspeaker impedances of 2, 4, or 8 Ohms; you get all the power you paid for and the freedom to choose any loudspeaker.
WATTMETER
Swift, accurate response reveals program peaks so staying within the power limits of your loudspeakers is easy.
BALANCED INPUTS
Allows the use balanced cables for 40dB better rejection of induced noise.
MONO MODES
Mono-Bridge and Mono-Parallel modes enable the MC2102 to deliver a full 200 watts as a mono amplifier into 1,2,4,8 or 16 Ohm loads.
- Tube Compliment
- (8) KT88
- (4) 12AX7A Input Tubes
- (4) 12AT7 Driver Tubes
- Ceramic Tube Sockets with
- Gold-Plated Contacts
- Patented Unity Coupled Circuit with
- Bifilar-Wound Output Transformers
- Soft-Start Inrush Protection
- Remote Power Control Trigger
MC2102 Tube Power Amplifier Specifications
POWER OUTPUT STEREO
Minimum sine wave continuous average power output per channel, all channels operating is:
100 watts into 2 ohm load
100 watts into 4 ohm load
100 watts into 8 ohm load
POWER OUTPUT MONO PARALLEL
Minimum sine wave continuous average power output is: 200 watts into 1 ohm,
2 ohm or 4 ohm load.
POWER OUTPUT MONO BRIDGE
Minimum sine wave continuous average power output is: 200 watts into 4 ohm,
8 ohm or 16 ohm load
RATED POWER BAND
20Hz to 20kHz
TOTAL HARMONIC DISTORTION
0.05% max at any power level from 250 milliwatts to rated power output is:
0.5% for 2, 4 or 8 ohm loads (stereo)
0.5% for 1, 2 or 4 ohm loads (mono parallel)
0.5% for 4, 8, or 16 ohm loads (mono bridge)
FREQUENCY RESPONSE
20Hz to 20kHz, +0 / -0.25dB
10Hz to 100kHz, +0 / -3dB
SENSITIVITY
2.5V unbalanced inputs 5.0V balanced inputs
A-WEIGHTED SIGNAL-TO-NOISE RATIO
100dB below rated output
WIDE BAND DAMPING FACTOR
Greater than 18
OUTPUT LOAD IMPEDANCE
Terminals for 2, 4, or 8 ohms (stereo)
Terminals for 1, 2, or 4 ohms (mono parallel)
Terminals for 4, 8, or 16 ohms (mono bridged)
INTERMODULATION DISTORTION
SMPTE 0.5% maximum if instantaneous peak output does not exceed twice the
output rating.
INPUT IMPEDANCE
20,000 ohms (unbalanced)
40,000 ohms (balanced)
POWER REQUIREMENTS
120V, 50/60Hz, 5.0A
OVERALL DIMENSIONS
(H x W x D including feet and knobs)
10-1/8” (25.72cm) x 17-3/4”
WEIGHT
88 lbs. (40.87kg) net
121lbs. (54.9kg) in shipping carton
For the Consumer's Protection
In order to ensure the highest level of customer satisfaction, "new" McIntosh products may only be purchased over-the-counter or delivered and installed by an Authorized McIntosh Dealer.
McIntosh products that are purchased over the Internet, by phone or mail order are presumed to be "used" and do not qualify for any McIntosh Warranty. McIntosh does not warrant, in any way, products that are purchased from anyone who is not an Authorized Dealer or products that have had their serial number altered or defaced.
